Ինչի՞ վրա պետք է ուշադրություն դարձնենք PCBA մշակման ժամանակ: Կետեր, որոնք ուշադրության կարիք ունեն PCBA մշակման մեջ

SMT proofing-ը պրոֆեսիոնալ PCBA մշակման արտադրող է իր սեփական PCB գործարանով և SMT կարկատանի մշակման գործարանով, որը կարող է ապահովել մեկ կանգառ PCBA processing services such as PCB proofing, component purchasing, SMT patch, dip plug-in, PCBA testing, finished product assembly and so on. Here are the matters needing attention in PCBA processing.


Խնդիրներ, որոնք պետք է դիտարկվեն PCBA-ի արտադրության մեջ
1. Ավտոմատ արտադրական գծում մեկ տախտակի փոխանցման և տեղադրման տարրերի նախագծում
Արտադրության գծի ավտոմատ հավաքման համար PCBA-ն պետք է ունենա եզրային և օպտիկական դիրքավորման նշաններ փոխանցելու հնարավորություն, ինչը արտադրողականության նախապայման է:
2. PCBA assembly process design
PCBA-ի առջևի և հետևի մասերի դասավորության կառուցվածքը որոշում է գործընթացի մեթոդը և ուղին հավաքման ընթացքում:
3. Component layout design
Նախագծեք բաղադրիչների դիրքը, ուղղությունը և տարածությունը հավաքման մակերեսի վրա: Բաղադրիչների դասավորությունը կախված է ընդունված եռակցման մեթոդից: Եռակցման յուրաքանչյուր մեթոդ ունի բաղադրամասերի դասավորության դիրքի, ուղղության և տարածության հատուկ պահանջներ:
4. Ժողով process design
For the design of welding pass through rate, through the matching design of pad, resistance welding and steel mesh, the quantitative and fixed-point stable distribution of solder paste is realized; Through the design of layout and wiring, the synchronous melting and solidification of all solder joints in a single package can be realized; Through the reasonable connection design of the mounting hole, 75% tin penetration rate can be achieved. These design goals are ultimately to improve the welding yield.


Precautions for PCBA welding
1. The warehouse keeper shall wear anti-static gloves when issuing materials and testing IQC, and the instrument shall be reliably grounded, and the worktable shall be paved with anti-static rubber pad in advance.
2. Գործողության ընթացքում օգտագործվում են հակաստատիկ աշխատասեղաններ, իսկ հակաստատիկ տարաներ՝ բաղադրիչները և կիսաֆաբրիկատները պահելու համար։ Բաժանմունքի եռակցման սարքավորումները կարող են հիմնավորվել, իսկ էլեկտրական զոդման երկաթը պետք է լինի հակաստատիկ տիպի: Օգտագործելուց առաջ բոլոր սարքավորումները պետք է փորձարկվեն:
3. When PCBA is processed through the furnace, because the pins of plug-in elements are washed by tin flow, some plug-in elements will tilt after welding, resulting in the element body exceeding the silk screen frame. Therefore, the repair welding personnel after the tin furnace are required to correct it properly.
4. When PCBA is welding horn and battery, it shall be noted that the solder joint shall not be too much, which shall not cause short circuit or falling off of surrounding components.
5. PCBA substrates shall be placed neatly, and bare plates cannot be stacked directly. If stacking is required, it shall be packed in electrostatic bags.

Precautions for PCBA finished product assembly
1. The whole machine without shell uses anti-static packaging bag
Պարբերաբար ստուգեք հակաստատիկ գործիքները, կարգավորումները և նյութերը՝ համոզվելու համար, որ աշխատանքային վիճակը համապատասխանում է պահանջներին:
2. When assembling finished products, follow the following procedures
Warehouse → production line → production line upgrade software → assembly into a complete machine → QC test → write IMEI number → QA full inspection → restore factory settings → warehousing; The software shall be upgraded before assembly. It cannot be assembled into a finished machine and then upgraded. It may not be upgraded due to improper welding, short circuit, operation process problems, etc., resulting in misjudgment of bad PCBA.


Վերոհիշյալն այն է, ինչն ուշադրության կարիք ունի PCBA մշակման մեջ: PCBA-ի մշակումը պետք է ուշադրություն դարձնի կետերի ներդրմանը, հուսով եմ, որ այն կարող է օգնել ձեզ: