如何清洁PCB?

印刷电路板,尤其是手机等 PDA(个人数字助理)中使用的那些,很容易被滥用。 In addition to collecting dust that can seep into the case of a phone, PCBS are also prone to soaking in or splashing out of liquids during daily use on e-book readers and similar handheld devices. 因此,出现了一个服务行业,为受污染的 PCBS 提供清洁和维修服务,但不会对 PDA 和大型设备造成物理损坏。

印刷电路板

Cleaning printed circuit boards (PCBS) to repair high-purpose products is as delicate a process as making circuit boards. 如果使用错误的清洁方法,可能会损坏连接、松动组件和损坏材料。 To avoid these defects, you need to take as much care in choosing the right cleaning method as you do in designing, specifying, and manufacturing boards.

这些陷阱是什么? How can they be avoided?

下面,我们将探讨经过验证的 PCB 清洁选项以及您可能不想使用的一些选项。

不同类型的污染物

All kinds of pollutants can accumulate on PCBS. Using the right response to an annoying problem will be more effective and will reduce headaches.

干燥污染物(灰尘、污垢)

最常见的情况之一是灰尘积聚在 PCB 内部或周围。 使用小巧精致的刷子(如马毛刷)轻轻去除灰尘,而不会影响组件。 There is a limit to where even the smallest brush can reach, such as under the component.

压缩空气可以到达许多区域,但会损坏重要的连接,因此使用时应小心。

A specially designed vacuum cleaner for electronic components is also an option, but it is ubiquitous.

湿污染物(污垢、蜡质油、助焊剂、苏打水)

High-temperature operations can turn certain wax-coated components into magnets for dust and dirt, resulting in sticky grime that can’t be removed with a brush or vacuum cleaner. 否则,产品会粘上苏打水并弄乱电路板。 Either way, these substances should be addressed before they accumulate and affect performance.

大多数污渍可以用清洁剂去除,例如异丙醇 (IPA) 和棉签、小刷子或干净的棉布。 仅在通风良好的环境中使用 IPA 等溶剂清洁 PCB,最好在通风橱中。

您可以使用去离子水代替。 Be sure to remove excess moisture and dry the plate properly (a few hours in a low oven will help remove any remaining moisture.)

In addition to IPA, there are many commercially available PCB cleaners, ranging from acetone to chemicals used to clean electronic equipment. 不同的清洁剂可以处理特定类型的污染物,例如助焊剂或蜡。 Keep in mind that harsh cleaners can remove marks from components or damage plastic or electrolytic capacitor jackets or other exotic components (such as humidity sensors), so make sure that the cleaner you use is not too strong. 如果可以,您无需在旧组件或连接器上测试清洁剂以确保不会造成太大损坏。

超声波PCB清洗

使用高频超声波清洗机会产生气穴现象。 超声波清洗机槽中含有的清洗液中数十亿个微小气泡的剧烈内爆。 The bubbles are generated by a transducer attached to the bottom of the tank and are excited by the generator at an ultrasonic frequency. 这些气泡的破裂会被零件清洁表面的污染物吹走。

超声波可以定义为频率高于人类听觉正常范围上限的声波,即约20 kHz(每秒20 kHz或20,000个周期)。 事实上,由于我们所说的超声波空化效应,在操作过程中可以听到超声波清洁器的声音。

该技术失去了作为清洁方法的一些优势,因为它会导致组件损坏或连接松动以及灰尘和污垢。 事实上,美国宇航局已经发布指令不要使用超声波清洗,因为它可能会无意中导致组件端盖分离,实际上会损坏 IC 内部的焊线以及焊线焊盘能量通过 IC 引线框架的超声波传导。

话虽如此,还是有可以使用超声波清洗的地方。 超声波清洗工艺可以到达电路板大部分部位的高密度组件下方最困难、难以到达的位置。 对于具有小于清洁液表面张力系数的小间隙的 SMD 设备,情况并非如此。 但是,该过程很快,并且有许多大容量机器可以处理大量清洁工作。

PCB超声波清洗机

空化不是一个温和的过程。 据计算,在空化气泡的破裂部位将产生超过 10,000°F 的温度和超过 10,000 PSI 的压力。

超声波清洁器可以产生从 25 kHz 到 100+ kHz 的频率,以每秒周期数为单位。 与较高频率相比,较低频率会产生更大的空化气泡。 较大的气泡会更猛烈地破裂,例如从制造的金属部件中去除全部污染物。 更高的频率会产生更小的气泡,使气泡清洁更温和,但更能穿透裂缝、裂缝和盲孔。 较高的频率用于清洁高度抛光或易碎的表面。

结论

有专门从事PCB清洗的公司。 根据您的需求(例如大量木板、需要清洁的物品以及木板的脆弱程度),您可以寻找合适的外部来源来满足您的清洁需求。

如果您经常遇到需要清洁的电路板问题,那么在设计或制造过程中可能需要检查更重要的事情。

清洁 PCBS 并不是一项艰巨的任务。 牢记上述提示和建议将有助于确保正确完成清洁。