Tuhinga o mua PCB hanga ko te whakarite me te tirotiro i te Tahora PCB. Ka whakawhiwhia ki te tipu hanga PCB nga konae CAD mai i te kamupene hoahoa PCB. I te mea kei ia raupaparorohiko CAD tona ake momo konae, ka hurihia e te tipu PCB ki tetahi whakatakotoranga honohono – Toroa Gerber RS-274X, Gerber X2 ranei. Then the engineer of the factory will check whether the PCB layout conforms to the production process, whether there are any defects and other problems.

I tetahi o nga PCBS i hangaia e te kaainga, ko te whakatakotoranga PCB ka taia ki runga pepa peita taiaho a ka whakawhiti ki tetahi papa-parahi. Heoi, i roto i te mahi taarua, na te mea he pai ki te kore o te waituhi i te waahi pakaru, me whakakii a ringa i te mangumangu ki te pene hinu.

He iti noa te waahanga hanga he pai, engari ki te whakawhitihia tenei koha ki te mahi umanga, ka tino whakaitihia te kaha o te mahi. Therefore, the factory generally adopts the way of photocopying, printing the PCB layout on the film. If it is a multi-layer PCB, the layout of each layer will be arranged in order.

The film is then punched with counterpoint holes. Counterpoint holes are very important, and are then used to align materials on each layer of the PCB.

Te mahi poari matua

Clean the copper clad plate, if dust may cause the final circuit short circuit or break.

The figure below is an illustration of an 8-layer PCB, which is actually made up of 3 copper-clad plates (core boards) plus 2 copper films and then glued together with semi-cured sheets. The production sequence starts from the core board (four or five layers of lines) in the middle, and is continuously stacked together before being fixed. He rite te hanga o te PCB 4-paparanga, engari kotahi noa te pereti matua me nga kiriata parahi e rua.

Transfer of inner PCB layout

Therefore, the two-layer circuit of the most central Core plate should be made first. After the copper-clad plate is cleaned, the surface is covered with a photosensitive film. The film solidifies when exposed to light, forming a protective film over the copper foil of the copper-clad plate.

Insert two layers of PCB layout film and two layers of copper clad board, and finally insert the upper layer of PCB layout film to ensure that the upper and lower layers of PCB layout film stacking position is accurate.

Photosensitizer uses UV lamp to irradiate the photosensitive film on copper foil. The photosensitive film is solidified under the transparent film, and the photosensitive film is not solidified under the opaque film. The copper foil covered by solidified photosensitive film is the PCB layout line needed, equivalent to the role of laser printer ink of manual PCB. In the paper PCB layout of the previous laser printer, the black toner was covered with copper foil to be retained. In this case, the copper foil covered with black film will corrode away, while the transparent film will be preserved as the photosensitive film solidifies.

Katahi ka horoia te kiriata kore rongoa ki te waikano, ka kapi i te kiriata whakaora i te ara iahiko konumohe parahi.

Inner core board etching

The unwanted copper foil is then etched away with a strong base, such as NaOH.

Tear off the cured photosensitive film to expose the copper foil needed for PCB layout circuit.

Ko te keri pereti Core me te tirotiro

Kua oti pai te pereti matua. Then make the opposite hole in the core plate for easy alignment with other raw materials.

Ka peehia te papa matua me etahi atu papa o PCB, kaore e taea te whakarereke, na he mea tino nui ki te tirotiro. Ka whakataurite te miihini ki nga tuhi whakatakotoranga PCB hei tirotiro i nga hapa.

Ko nga papa tuatahi e rua o nga papa PCB kua hangaia

kua whakairohia

Here we need a new raw material called semi-cured sheet (Prepreg), which is the core board and core board (PCB layer number & GT; 4), and the adhesive between the core plate and the outer copper foil, but also plays a role in insulation.

The lower layer of copper foil and two layers of semi-solidified sheet have been in advance through the positioning hole and the lower iron plate fixed position, and then the good core plate is also put into the positioning hole, and finally in turn two layers of semi-solidified sheet, a layer of copper foil and a layer of pressure aluminum plate covered on the core plate.

In order to improve work efficiency, the factory will stack three different PCB boards together and then fix them. The upper iron plate is magnetically attracted to facilitate counterpoint with the lower iron plate. Through the placement of the counterpoint needle, the two layers of iron plate counterpoint successfully, the machine as far as possible to compress the space between the iron plate, and then fixed with nails.

PCB board clamped by iron plate is placed on the support, and then into the vacuum hot press for lamination. The heat in the vacuum hot press melts the epoxy resin in the semi-cured sheet, holding the core and copper foil together under pressure.

After laminating, remove the top iron plate that presses the PCB. Na ka tangohia te pereti konumohe pressurized. Ko te pereti konumohe tetahi mea nui ki te wehe i nga PCBS rereke me te whakarite kia maeneene te parahi parahi i te papa o waho o TE PCB. Both sides of the PCB are covered with a layer of smooth copper foil.

kōhao

Me pehea te hono i nga papa parahi e wha o te peera parahi kore ki te PCB? Ko te PCB i te tuatahi ka werohia ki roto i nga rua, katahi ka whakarewaina hei kawe hiko.

Ka whakamahia te miihini taraiwa X-ray ki te rapu i te papa matua o te papa o roto. Ka kitea e te miihini te waahi ka kitea te waahi o te kohao ki runga i te papa matua, ka huri ana i nga poka ki te PCB kia mohio ai ko te keri e whai ake nei kei waenga i te waahi o te kohao.

Place a sheet of aluminum on the punch machine and then place the PCB on top. I te mea he tere te mahi keri, kia pai ake ai te whakapai ake, 1 ki te 3 nga papa PCB rite tonu mo te whakakotahitanga kia rite ki te maha o nga papa PCB. Finally, the top PCB is covered with a layer of aluminum, the top and bottom layers of aluminum so that when the drill drills in and out, the copper foil on the PCB will not tear.

The operator then only needs to select the correct drilling procedure and the drilling machine does the rest automatically. Ko te miihini taraiwa e akiakihia ana e te hau, me te takahuri o te 150,000 hurihanga ia meneti, he tiketike rawa hei whakarite i te pakitara poka maeneene.

Ko te whakakapi i te waahanga drill ka mahia noa e te miihini kia rite ki te kaupapa. The smallest drill can be 100 microns in diameter, while a human hair is 150 microns in diameter.

I roto i te mahinga rongoa o mua, i tukuna te epoxy rewa ki waho o te PCB, no reira me tango atu. Ko te miihini miihini miihini ka tapahi i te taha o te PCB kia rite ki nga taunga XY tika.

Te maturuturu o te matū o te parahi i runga i te pakitara o te koiwi

Since almost all PCB designs use perforations to connect different layers of lines, a good connection requires a 25 micron copper film on the hole wall. This thickness of copper film is achieved by electroplating, but the hole wall is made of non-conductive epoxy resin and fiberglass board. Na reira, ko te mahi tuatahi ko te kohikohi i tetahi waahanga o nga mea kawe ki runga i te pakitara poka, me te hanga i te kiriata parahi 1-micron ki te mata PCB katoa, tae atu ki te pakitara poka, na roto i te putunga matū. Ko te mahinga katoa, penei i te maimoatanga matū me te horoi, ka whakahaerehia e nga miihini.

Fixed PCB

Whakapai i te PCB

Delivery of PCB

Chemical precipitation of copper film

Transfer the layout of the outer PCB

Next, the layout of the outer PCB will be transferred to the copper foil. The process is similar to that of the PCB layout of the inner core board, which is transferred to the copper foil using photocopied film and photosensitive film. The only difference is that the positive plate will be used as the board.

The transfer of inner PCB layout introduced above adopts the subtraction method and adopts the negative plate as the board. PCB covered by solidified photosensitive film is circuit, clean the unsolidified photosensitive film, exposed copper foil is etched, PCB layout circuit is protected by solidified photosensitive film. The outer PCB layout is transferred by the normal method, and the positive plate is used as the board. The area covered by a cured film on a PCB is a non – line area. After cleaning the uncured film, electroplating is carried out. Kaore he kiriata ka taea te hiko, kaore hoki he kiriata, ko te parahi tuatahi katahi ka whakakikorua i te tine. Whai muri i te tangohanga o te kiriata, ka whakahaerehia te etching alkaline, ka mutu ka tangohia te tine. The circuit pattern is left on the board because it is protected by tin.

Clean both sides of the copper foil PCB into the press, the press will be sensitive to the copper foil mold pressing.

Whakatikahia te kiriata whakatakotoranga PCB o nga waahanga o runga me o raro o te kape whakaahua na roto i te kohao whakanoho, ka tuu i te papa PCB ki waenganui. The photosensitive film under the transmittance film is then solidified by UV lamp irradiation, which is the line that needs to be preserved.

After cleaning the film that is not needed and has not been cured, inspect it.

Clamp the PCB and electroplate the copper. As mentioned before, in order to ensure that the hole has good electrical conductivity, the copper film electroplated on the hole wall must have a thickness of 25 microns, so the whole system will be automatically controlled by computer to ensure its accuracy.

Fixed PCB

Computer control and electroplating copper

After the copper film is electroplated, the computer arranges for a thin layer of tin to be replated.

After unloading the tin plated PCB board, check to ensure that the thickness of copper and tin plating is correct.

Tauhou PCB waho

Next, a complete automated assembly line completes the etching process. First, clean off the cured film on the PCB board.

A strong alkali is then used to clean off unwanted copper foil that is covered by it.

Na ka tangohia te paninga tine kei runga i te papa parahi o te whakatakotoranga PCB me te otinga takai whakarere. After cleaning, 4 layers PCB layout is completed.