PCB ngosi nhazi nhazi

PCB blanking, oghere na nhazi nhazi nwere ike ịnabata usoro ịnwụ anwụ, maka ịhazi PCB ma ọ bụ PCB na -enweghị oke chọrọ nwere ike ịnabata usoro oghere. Kwesịrị ekwesị maka imepụta ọkwa dị ala na PCB buru ibu na -enweghị nnukwu ihe achọrọ yana ọ bụghị oke ụdị chọrọ, yana ọnụ ala.

Punch:

Mmepụta nke nnukwu ogbe, ụdị na ọnụ ọgụgụ oghere na ụdị dị mgbagwoju anya nke mkpụrụ akwụkwọ nwere otu akụkụ yana oghere nwere oghere nwere ihu abụọ nke epoxy iko, na-ejikarị otu ma ọ bụ ọtụtụ nwụọ.

Nhazi nhazi:

Mbipụta imepụta bọọdụ buru ibu buru ibu otu panel na udi nke okpukpu abụọ, na -abụkarị site na ịnwụ. Dika nha bọọdụ e biri ebi, enwere ike kewaa ya na elu ma nwụọ.

Nhazi mejupụtara:

In order to shorten the manufacturing cycle and improve productivity, composite die is used to process the holes and shapes of single panel at the same time.

Iji jiri ebu na -edozi bọọdụ e biri ebi, isi ihe bụ nhazi na nhazi nke ebu, nke chọrọ ihe ọmụma ọrụ aka ọrụ. Tụkwasị na nke ahụ, nrụnye na mbughari nke ebu dịkwa ezigbo mkpa. Ugbu a, ọtụtụ n’ime ebu nke PCB emepụta na -esichara site mpụga ụlọ mmepụta ihe.

Nlekọta anya maka nrụnye ebu:

1. Dabere na ngụkọta oge ọnwu nke ike oghere, nha nke anwụ, ịdị elu mmechi nke nhọrọ pịa (gụnyere ụdị, tonnage).

2. Start the punch, check the clutch, brake, slider and other parts are normal, the operating mechanism is reliable, there must be no continuous impact phenomenon.

3. Igwe mpe mpe akwa dị n’okpuru anwụ, na -abụkarị iberibe 2, a ga -etinyerịrị ya na igwe igwe nri n’otu oge, iji hụ na etinyere nwụnye ya na vetikal. Kpachie oghere ọnụnọ nke ọkwa mmamịrị nke na -anaghị egbochi ihe ịdaba n’otu oge ahụ na nso etiti ebu.

4. Kwadebe ọtụtụ usoro ịpị efere na T-isi ịpị kposara efere maka iji kwekọrọ na iji ya na ebu. Ngwụcha ihu efere efere ekwesịghị imetụ mgbidi kwụ ọtọ nke anwụ anwụ ala. Ekwesịrị idobe akwa emery n’etiti oghere kọntaktị yana kposara ga -akpachapụ anya.

5. Mgbe ị na -etinye ebu ahụ, attentionaa ntị na kposara na mkpụrụ dị na ala anwụ anwụ ka ị ghara imetụ elu aka (elu anwụ na -ada wee mechie).

6. Mgbe ị na -ahazi ebu, gbalịa jiri akwụkwọ ntuziaka karịa moto.

7. Iji meziwanye arụmọrụ blanket nke mkpụrụ ahụ, mkpụrụ akwụkwọ kwesịrị ịdị ọkụ. Okpomoku ya rue 70 ~ 90 ℃ kacha mma.

Oghere na udi nke bọọdụ na -achaghị acha na -ebipụta nwere ntụpọ ndị a:

Ewelitere gburugburu oghere ma ọ bụ foil ọla kọpa ma ọ bụ kpuchie ya; Enwere ntụpọ n’etiti oghere; Oghere ọnọdụ ma ọ bụ oghere n’onwe ya abụghị kwụ ọtọ; Burr; Ngalaba siri ike; A na -agbatị bọọdụ e biri ebi n’ime ala ite ahụ; Scrap na -awụlikwa elu; Jam na -ala n’iyi.

Usoro nyocha na nyocha dị ka ndị a:

Lelee ma ike ọkpọ na nkwụsi ike nke igwe ntụtụ nwere ezuru; Ọnwụ anwụ nwere ezi uche, nke siri ike; Convex, concave die na kọlụm ntuziaka, a na -enweta izizi nke aka uwe na -arụ ọrụ, nrụnye na -etinye uche, kwụ ọtọ. Ma nkwachapụ dabara adaba bụdị. Oghere dị n’agbata convex na concave pere mpe ma ọ bụ buru oke ibu iji mepụta ntụpọ dị mma, nke bụ nsogbu kachasị mkpa na nhazi, nhazi, nchapu na ojiji. Agaghị ekwe ka okirikiri na conveve die n’ọnụ ya gbaa okirikiri na ime ụlọ. A naghị ekwe ka Punch nwee taper, ọkachasị mgbe anabataghị ịpị ma ndị nkịtị na ndị nke akpọrọ akpọgharị. N’ime imepụta ihe, anyị kwesịrị ị paya ntị mgbe niile ma a na -eyi nsọtụ convex na concave anwụ. Ọnụ ọpụpụ bụ ihe ezi uche dị na ya, obere nguzogide. Push the material board, the material rod is reasonable, enough force. Ọkpụrụkpụ nke efere na ike njikọ nke mkpụrụ ahụ, ego nke gluu, na ike njikọ nke foil ọla, okpomọkụ na iru mmiri na oge bụkwa ihe a ga -atụle na nyocha nke ntụpọ adịghị mma.